How To Repair Port On Galaxy S6 Self
Repair guide : Charging connector Samsung Milky way S6 Edge +
Level : Very hard Fourth dimension : threescore min Author : Alexandre
135 people have done this repair successfully ! Why not you lot?
Has yourSamsung Galaxy S6 Edge + been giving you trouble when you try to charge information technology, making you more than infuriated than you are worried about it every unmarried day? Well you're in the correct identify to ready your issues, as the experts at SOSav prepared thisrepair guide just for yous. You can now replace the charging connectoryourself, saving up to three times the price of a professional repairer. It'due south your move :P
Problems:
- Charging issues
- Damaged charging connector
Some advice before you kickoff
Recommended repair kit
Stride 1
Before proceeding to replace the charging connector of your Galaxy S6 Edge Plus you must, for evident safety reasons, plough off your device.
To exercise this, concur down the off button for a few seconds, then ostend by selecting "off".
Pace 2
Insert the SIM tray opening tool into the hole to open the tray, situated on the top edge of the phone, then button softly on the tool to extract the SIM tray.
Accept concur of the tray and then remove information technology.
The SIM tray and the SIM carte of your Milky way S6 Edge + are now removed.
Footstep 3
The rear panel of your Galaxy S6 Edge + is glued to its frame. It is necessary to "soften" the clue using a hair dyer. To do this, oestrus the bottom and acme parts of the rear panel for xx-30 seconds maximum.
Do non heat the rear panel of your S6 Border + for longer than twenty-thirty seconds, as you might damage the NFC cable/induction charging role.
Step 4
Place an opening selection in the lesser right corner of the rear panel.
Place another opening choice at the tiptop correct corner of the rear panel, sliding it from the bottom corner to the top to place it.
Next insert a third opening choice in the pinnacle left corner, sliding it equally you do. Repeat for the terminal opening pick in the bottom left corner
This step volition simplify the removal of the rear panel.
Footstep 5
Take concord of the two picks on the left side of the telephone, then delicately lever them up in order to unfix the rear console from the frame of the phone.
Elevator information technology, and then remove the rear console.
The rear console of your Galaxy S6 Border + is now removed.
Stride 6
Using a cantankerous headed screwdriver, unscrew the 17 screws that secure the internal frame of the phone, circled in the paradigm in red.
Step seven
Take hold of the internal frame and so remove information technology.
The frame should detach from the residue of the phone very easily.
The frame of your Galaxy S6 Edge + is now removed.
Footstep 8
Using a spudger, disconnect the bombardment cablevision attached to the logic board.
Step 9
Insert an opening pick very carefully into the bottom right corner of the battery.
Have a 2nd choice and insert information technology into the lesser left corner of the bombardment.
Step ten
Grasp the pick on the bottom right and slide it to the top correct corner in guild to detach the right side of the battery.
Exercise this again for the left side of the battery.
Take intendance to ensure you don't pierce or damage the battery!
Step eleven
Then accept hold of the bombardment and go on to remove it.
The bombardment of your Galaxy S6 Edge + is now removed.
Footstep 12
Utilise the nylon spudger to disconnect the internal speaker connector cable.
So use the tweezers to grasp and remove the internal speaker.
The internal speaker of your Milky way S6 Edge + is now removed.
Step xiii
Proceed using the nylon spudger, and disconnect the connector cable for the calorie-free and proximity sensor.
Then disconnect the LCD screen cable.
Step xiv
Using the pointed edge of the spudger, disconnect the WiFi/Bluetooth and GSM cables.
Step fifteen
Elevator the logic board from the top border using the nylon spudger, then flip it over every bit indicated in the images for this footstep.
Step 16
Disconnect the connector cable for the charging port with the nylon spudger.
And so grasp the logic board and remove from the phone.
The logic lath of your Galaxy S6 Edge Plus is at present removed.
Step 17
Using the tweezers, grasp the GSM interconnect cablevision on ane side (as seen in the image) and remove information technology from its place.
So utilize the pointed terminate of the spudger to disconnect it from the charging connector side.
Pace 18
Grasp the interconnect cable over again with tweezers, and so remove it.
The GSM interconnect cable of your Galaxy S6 Edge + is at present removed.
Step 19
Employ the tweezers to grasp the WiFi/Bluetooth cable, then delicately lift it.
Step 20
Using the pointed end of the nylon spudger, disconnect the cable from the charging connector.
Choice up the interconnect cable and remove it.
The WiFi/Bluetooth interconnect cablevision of your Milky way S6 Edge + is now removed.
Step 21
Once again using the nylon spudger, disassemble the proximity and brightness sensor from the frame of the phone.
You can now remove the sensor.
The proximity and brightness sensor on your Milky way S6 Edge + is now removed.
Step 22
Using the pointed edge of the nylon spudger, delicately unfix the vibrator and then remove information technology.
Step 23
Using a hair dryer, rut the entire frame to soften the glue.
Step 24
Insert a plastic menu, every bit indicated in the photo, in order to remove the frame from the screen.
Pace 25
Continue to unfix the frame.
The part of the screen underneath is very fragile. Exercise not forcefulness the frame up. Reheat information technology if at that place is resistance.
Footstep 26
Insert the plastic carte du jour into the bottom office of the frame, as indicated in the photos. You can cut the plastic menu in half to brand the chore a little easier.
Stride 27
Insert the nylon spudger in guild to lever upward the frame, and to completely unfix it from the screen.
Stride 28
Utilize the nylon spudger to tip the frame upwards.
The frame can now exist completely removed.
Step 29
Using the nylon spudger, unfix the shortcut button from the frame.
Step 30
Repeat this pace for the shortcut button on the left.
Pace 31
Turn the frame over to unclip the home push cable from the charging connector.
Step 32
Lever upward the charging connector in order to remove it from the frame.
Step 33
The charging connector of your Galaxy S6 Edge + is now removed from the frame.
If you're having charging issues, replace the charging connector with a new one.
Recommended repair kit
Source: https://www.sosav.com/guides/mobiles/samsung/galaxy-s6-edge-plus/charging-connector/
Posted by: jacksonorwil1936.blogspot.com
0 Response to "How To Repair Port On Galaxy S6 Self"
Post a Comment